GSM Click is an add-on board in mikroBUS™ form factor which is a perfect solution for adding GSM/GPRS communication layer to your device. It features Telit GL865-QUAD GSM/GPRS module which supports GSM/GPRS 850/900/1800/ 1900 MHz Quad-band frequency. The board contains a TXB0106 6-bit bidirectional voltage-level translator as well as a SIM card socket. GSM Click communicates with the target microcontroller via seven mikroBUS™ lines (RX, TX, INT, PWM, CS, RST and AN). The board can use either 3.3V or 5V power supply. LED diode indicates the presence of power supply.
Mitgliederpreis 57,00 $
GSM2 Click is an add-on board in mikroBUS™ form factor which is a perfect solution for adding GSM/GPRS communication layer to your device. It features the Quectel M95 FA GSM/GPRS module which supports GSM850MHz, GSM900MHz, DCS1800MHz or PCS1900MHz quad-band frequencies with 85.6 kbps GPRS data transfer. The board contains a quadrupole audio/microphone jack, SMA antenna connector, as well as the SIM card socket. GSM Click communicates with the target microcontroller via seven mikroBUS™ lines (RX, TX, INT, PWM, CS, RST and AN). The board can use either 3.3V or 5V power supply and I/O voltage levels. LED diode indicates the presence of power supply.
Mitgliederpreis 52,00 $
RFID Click™ is an accessory board in mikroBUS™ form factor. It’s a compact and easy solution for adding RFid to your design. It features a CR95HF 13.56 MHz contactless transceiver as well as a trace antenna. RFid click™ communicates with the target board microcontroller via mikroBUS™ UART (TX, RX), SPI (MISO, MOSI, SCK, CS) INT, RST, PWM and AN lines. The board is designed to use 3.3V power supply only. LED diode (GREEN) indicates the presence of power supply. CR95HF IC is a RFid module with an integrated transceiver for contactless applications. The board contains a dedicated internal frame controller and an analog front end (AFE) for RF communications.
Mitgliederpreis 35,00 $
RS232 Click is a simple solution for adding RS232 connectivity to your design. RS232 is a serial communications standard mostly used for industrial machines, networking equipment and scientific instruments, as well as for computer peripherals. The board features a standard RS232 DB9 port and a MAX3232 IC, along with a mikroBUS™ host socket, three jumpers and a power indicator LED. RS232 click communicates with the target board through mikroBUS™ RX (RXD), TX (TXD), CS (RTS), and INT (CTS) lines. RS232 click is designed to use either a 3.3V or 5V power supply.
Mitgliederpreis 18,00 $
RELAY Click™ board features two G6D1AASI-5DC power PCB relay modules as well as two screw terminals. It communicates with target microcontroller via mikroBUS™ PWM (RL1) and CS (RL2) pins. LED diode (Green) indicates the presence of power supply. Control up to 5A, 250V AC/30V DC loads. The board is designed to use 5V power supply only, but communication lines voltage level can be in range between 1.8V and 5V. On-board transistors are used to drive relays by current sinking.
Mitgliederpreis 22,00 $
It just clicks
Click add-on boards are the easiest way to add sensors, human interface, control, or wireless communications interfaces to your design.
Based on the mikroBUS™ interface standard from Mikroelektronika, click boards™ add incredible capability to any system with ease.
No wires, no soldering, no time-wasting. Libraries and examples available.